The whip is compatible with all below mounts
ML 3-XR
¼ λ Mobile Antenne for the 80 MHz Band
Description
- Black-chromed, conical stainless steel whip with shock spring.
- Whip design for optimum wind noise reduction.
- Elegant transition between whip and mounting surface due to slim-line mount.
- 30° tiltable whip.
- Ideal for installation on the narrow strip on rear wing between trunk lid and side of car.
- Stainless steel X-mount with M6-thread whip-fastening system.
- Simple mounting exclusively with access from the outside.
- Models available with X-mount (oblong) and CX-mount (circular).
- Choice between two connection principles:
- X-mount: FME-connection (supplied without cable).
- XP4-mount: Permanently attached 4 m cable terminated with FME-connector.
Specification
| Electrical | |
| Model | ML 3-XR |
|---|---|
| Frequency | Tunable by cutting within : 66-88 MHz (Also applicable : 88-175 MHz) |
| Antenna Type | Mobile whip antenna |
| Max. Input Power | 250 W |
| Polarisation | Vertical |
| Impedance | 50 Ω |
| VSWR | ≤ 1.3:1 @ f.res. |
| Bandwidth | ≥ 8 MHz @ VSWR ≤ 2.0 |
| Gain (EIA RS-329-1) | 0 dB |
| Mechanical | |
| Materials | Whip : Black-chromed, conical stainless steel Black-chromed brass Mount : Black-chromed brass Weather- and shockproof plastics Stainless steel |
|---|---|
| Installation Torque | 4 ±1 Nm |
| Colour | Black |
| Historic Brand | Amphenol Procom |
| Antenna Mount Type | Hole Mount |
| Height | Approx. 1100 mm / 43.31 in. |
| Weight | X-version : Approx. 110 g / 0.24 lb. XP4-version : Approx. 270 g / 0.6 lb. |
| Mounting | 18 mm dia. hole |
Ordering Codes
| Model | Product No. | Additional Information |
|---|---|---|
|
ML 3-XR |
130001457 | X-mount (oblong) with FME-system |
|
ML 3-CXR |
130000652 | CX-mount with FME-system (circular) |
|
ML 3-XP4R |
130001339 | XP4-mount with 4 m cable and FME-connector (oblong) |
|
ML 3-CXP4R |
130001435 | CXP4-mount with 4 m cable and FME-connector (circular) |
Additional Information
Installation
This antenna can be mounted anywhere on the vehicle.
The oblong X-mount is especially suited for mounting on the often very narrow strip on the rear wing between the trunk lid and the side of the car.
Mounting can take place exclusively with access frome the outside when drilling an 18 mm dia. hole. Mounting can take place from the inside by drilling a 14 mm dia. hole. When mounting in a 14 mm dia. hole, remove the bottom plastic ring of the packing gasket with a sharp cutter.
When cleaning the car in car-washing machines, remove the whip using a spanner, size 9 mm. After wash, refit the whip and tighten it lightly with the spanner.
As the mount is internally equipped with a bendable section, the antenna can always be adjusted to an upright position independent of the tilt angle of the installation spot (up to 30° tilt).
1. Installation Dimension
2. Installation Steps
Do not use sealer on rubber gasket or other places.
3. Tuning
The antenna should always be tuned using an VSWR-meter.
The cutting diagrams below serve as a guide for this procedure.
PROCOM A/S reserves the right to
amend specifications without prior notice
PROCOM A/S • Smedetoften 12
DK 3600 Frederikssund • Denmark
Generated : 2026-06-26
Version 1